Volkswagen Polo 3 with 1994 for 2001 of release.
1. The general data
2. The engine
3. Greasing system
4. Cooling system
5. Systems of injection of fuel
6. Ignition system
7. Coupling
8. A mechanical transmission
9. A drive of wheels
10. A steering without the amplifier
11. A steering with the hydraulic amplifier
12. A forward suspension bracket
12.1. Removal and installation absorber racks
12.2. Dismantling absorber racks
12.3. Repair absorber racks
12.4. Assemblage absorber racks
12.5. Removal and installation of separate details of a suspension bracket
12.5.1. Replacement of spherical support
12.5.2. Removal and installation of the lever of a suspension bracket
12.5.3. The control of spherical support
12.5.4. Removal and installation of the stabilizer of cross-section stability
12.6. A forward stretcher
13. A back suspension bracket
14. Brake system
15. An electric equipment
16. Heating and ventilation system
17. An automatic transmission
18. Appendices
 













12-5-2-snyatie-i-ustanovka-rychaga-podveski.html

12.5.2. Removal and installation of the lever of a suspension bracket

The suspension bracket lever can be removed in two ways. First, it is possible to turn away bolts of fastening of the lever on an inside and to disconnect the spherical hinge from absorber racks. The second way consists that it is possible to turn away bolts of fastening of the lever on an inside and the bolts connecting the spherical hinge and the lever on lateral aspect. It is possible to apply any way.
For removal it is necessary to execute the following:
- To weaken wheel nuts, to establish a forward part of the car on support and to remove a wheel;
- By means of a jack to raise cautiously lateral aspect of the lever (under a wheel nave);
- To remove the lever if the spherical hinge is on the lever for what to execute the following:
- To disconnect the spherical hinge in the way described above from the bottom party of the lever of a suspension bracket;
- On a lever inside ahead to turn out the bolt established sideways. A bolt will tighten the big moment;
- On a lever inside to turn out the bolt established from below;
- To disconnect the stabilizer of cross-section stability from the cross-section lever of a suspension bracket for what to turn away a nut which is on the bottom party. To remove a metal plate and a rubber support. To pay attention to how these details are established, especially on position of a metal washer. The rubber support is turned by the conic party to the cross-section lever of a suspension bracket;
- To lower a jack and to wring out the suspension bracket lever downwards while the pin of the spherical hinge does not leave from absorber racks;
- To liberate the lever. To push out the cross-section lever of a suspension bracket ahead from knot of fastening and to take out it behind from an aperture in a stretcher;
- To remove the lever from which the spherical hinge for what it is necessary is disconnected:
- On lateral aspect of the cross-section lever of a suspension bracket from below to note a contour of a plate of the spherical hinge that it could be fixed again bolts in initial position (see replacement of the spherical hinge);

Fig. 263. Fastening of the lever of a suspension bracket and the details established on it: 1 — draught of the stabilizer of cross-section stability; 2 — the plug of a support of a bar of the stabilizer; 3 — a plate with nuts; 4 — a nut, 35 Нм; 5 — the spherical hinge of a suspension bracket; 6 — bolts, 35 Нм; 7 — the stabilizer plug; 8 — a washer; 9 — a nut, 25 Нм; 10 — a bolt with шестигранной a head, 50 Нм + 90 ; 12 — дефлектор; 11, 13 — the notched rivets; 14 — a bolt with шестигранной a head, 70 Нм; 15 — a forward support of the cross-section lever of a suspension bracket; 16 — the suspension bracket lever; 17 — a back support of the lever of a suspension bracket




- To turn on from below three bolts 6 (fig. 263) fastenings of a plate of the spherical hinge see and to remove a plate 3 from the top party;
- A few to wring out outside амортизаторную a rack, to weaken connection;
- On an inside of a shoulder of the lever ahead to unscrew the bolt established sideways;
- On a lever inside to unscrew the bolt established from below;
- To lower a jack. To deduce the suspension bracket lever ahead, having pressed it, from a support and to take out it behind from an aperture in a stretcher.
Installation of the lever of a suspension bracket is spent to sequences, return to removal. The inhaling moments see the appendix and corresponding drawings. At installation of the spherical hinge to follow the instructions resulted in подразд. 12.5.1.



Back on page
12.5.1. Replacement of spherical support
On the following page
12.5.3. The control of spherical support